NIT8668UC Install Manual 2 - I.sears.com
Millboard covered with not less than no. 28 gauge sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) After unpacking the cooktop, unscrew the heat shield. The heat shield will be able to rotate freely, as shown in the illustration. Secure the cooktop to countertop ... Fetch Full Source
Saf-T Thimble - United States - Selkirk
The Heat-Fab Saf-T Thimble is intended for use in conjunction The wall protector and cover shield of the Saf-T Thimble should be installed on approved fire retardant sheetrock, millboard, ... Return Document
Www.hearth.com
SHIELD BOTTOM HEAT SHIELDS ATTACHABLE STRAIGHT LEG SPECIFICATIONS Be sure you have chosen the correct size heater for the area you intend to heat. minimum thickness asbestos millboard or equivalent (U.L. Listed floor protector). If ... View This Document
Installation Manual - Abt Electronics
Installation Manual Cooktop NIT5066UC, NIT5666UC, NIT8066SUC, millboard covered with not less than no. 28 gauge sheet metal, 0.015" unscrew the heat shield. The heat shield will be able to rotate freely, as shown in ... Access Document
Installation GUIDE - Ajmadison.com
Millboard covered with not less than no. 28 gauge sheet metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) After unpacking the cooktop, unscrew the heat shield. The heat shield will be able to rotate freely, as shown in the illustration. Secure the cooktop to countertop ... Document Retrieval
PACIFIC SPECIALTY INSURANCE COMPANY
(IF WOODSTOVE IS PRIMARY SOURCE OF HEAT OR DOUBLE VENTED, WALL PROTECTION: Asbestos Millboard Covered with Metal Metal Asbestos Millboard Other INCHES SIZE OF THIMBLE OR ROOF JOIST SHIELD DO THESE DISTANCES COMPLY WITH THE MANUFACTURERS STANDARDS? Yes No ... Retrieve Doc
MOBILE HOME APPLICATION - Rothert Insurance - Home
IS WOODSTOVE EQUIPPED WITH A HEAT RECLAIMING DEVICE? Yes No TYPE: Asbestos Millboard Covered with Metal Metal Stone/Brick Other (Specify) 7 _____ INCHES SIZE OF THIMBLE OR ROOF JOIST SHIELD DO THESE DISTANCES COMPLY WITH THE MANUFACTURERS STANDARDS? Yes No REMARKS: ... Get Document
MODELS SHOWN: CIT36XKB FREEDOM INDUCTION COOKTOP AND UCVM36FS ...
96 MODELS SHOWN: CIT36XKB FREEDOM™ INDUCTION COOKTOP AND UCVM36FS DOWNDRAFT. COOKTOPS — INDUCTION millboard, covered by no. 28 steel sheet 0.015 (.4 mm) HEAT SHIELD The heat shield will require an additional 1" clearance ... Fetch This Document
700 Wood Manual - Hearth & Home Technologies - Hearth N Home
FLUE TOP (WITH REAR HEAT SHIELD) Table I SIDEWALL CEILING Minimum Clearances to Combustibles Figure 2 Flue Rear Clearances 206750 Figure 1 Flue Top Clearances protect the millboard and give it a finished look. Any horizontal length of chimney connector pipe must ... Doc Viewer
52-BAY - Appalachian Stove
Stove (3/8” fireproof millboard or equivalent) for masonry fireplace. D) The 52 Bay stove must be installed with adequate clearance Combustible Wall-Insulated Pipe-Heat Shield 6” 24 ... Return Doc
Heat Shield Wood Stove Ideas Design Proper Masonry Brick ...
Most everyone thinks that a brick or stone wall behind a stove will protect it. NOT!!! A brick or stone wall easily conducts heat through it drying out and l ... View Video
TENMAT
Heat shield panels Splash guards High that will prevent heat damage to stopper arms of tundishes in the continuous casting process. The extremely high temperature of steel in a tundish can Millboard Protects stopper arm from deforming Prevents issues ... Retrieve Here
Fiber Cement Board / James Hardie ( What To Look For On Your ...
Http://www.DiamondSidingAndWindows.com When considering James Hardie Fiber Cement Board take a good look at your home. We at Diamond Contracting have seen a ... View Video
Stillwater Insurance Group - Wenner-Davis & Associates Insurance
Material must be at least 26 gauge metal or asbestos millboard mounted between stove or stove pipe and the heat shield may not be less than 15”. Stillwater Insurance Group PO BOX 45126, Jacksonville, Fl 32256-5126 Tel (800)849-6140; Fax ... View Document
36-INCH INDUCTION COOKTOP MODEL CIS365GB - Thermador.com
100 36-INCH INDUCTION COOKTOP MODEL CIS365GB SHOWN WITH 42-INCH ISLAND HOOD HGSI42TS. 1.800.735.4328 by not less than 1/4fletardant millboard, covered by no. 28 steel sheet 0.015 (.4 mm) HEAT SHIELD The heat shield will require an additional 1" clearance ... Read Here
WOOD / COAL / PELLET BURNING STOVE UNDERWRITING GUIDELINES - SCU
WOOD / COAL / PELLET BURNING STOVE UNDERWRITING GUIDELINES heat shield, which extends behind gauge metal or asbestos millboard mounted on spacers to provide a minimum of 1" air space between the shield and the wall. Minimum distance between stove ... Read Full Source
30 GAS RANGE INSTALLATION INSTRUCTIONS - The Home Depot
30" GAS RANGE INSTALLATION INSTRUCTIONS Clearances and Dimensions 1. millboard covered with not less than no. 28 MSG sheet steel, sure the floor covering can withstand heat at least 90°F above room temperature without shrinking, warping or ... View Doc
100 MODELS SHOWN: CIT36XKB FREEDOM INDUCTION COOKTOP AND ...
100 MODELS SHOWN: CIT36XKB FREEDOM® INDUCTION COOKTOP AND UCVM36FS DOWNDRAFT. retardant millboard, covered by no. 28 steel sheet 0.015 (.4 mm) HEAT SHIELD The heat shield will require an additional 1" clearance ... Fetch Here
Figure 2109.4 STOVE INSTALLATION CLEARANCES
STOVE INSTALLATION CLEARANCES Stove Components Combustible Material Asbestos Millboard Spaced Out 1” 2. Concrete/Masonry Foundation Wall Clearances on each side of a radiant stove with a heat shield shall be measured as if a circulating type. ... Access Content
HOW TO ORDER REPAIR PARTS Model 2941 WONDERWOOD - Rural King
Model 2941 WONDERWOOD THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR 30 Heat Shield 1 22110 31 Secondary Heat Shield 1 22030 * NOT SHOWN 17 combustible floor protector of one layer of 3/8" millboard having a thermal conductivity of. REPAIR PARTS. REPAIR PARTS. ... Doc Retrieval
No comments:
Post a Comment